diff --git a/README.md b/README.md
index 82cf1f8f..9d661934 100644
--- a/README.md
+++ b/README.md
@@ -39,7 +39,9 @@ As of now, here is the list of achievements of this project:
  - **[Experimental]** Bootloader based on [MCUBoot](https://juullabs-oss.github.io/mcuboot/)
  
 ## Documentation
+
 ### Build, flash and debug
+ - [Files included in the release notes](doc/filesInReleaseNotes.md)
  - [Build the project](doc/buildAndProgram.md)
  - [Bootloader, OTA and DFU](./bootloader/README.md)
  - [Stub using NRF52-DK](./doc/PinetimeStubWithNrf52DK.md)
diff --git a/doc/filesInReleaseNotes.md b/doc/filesInReleaseNotes.md
new file mode 100644
index 00000000..e9dadb24
--- /dev/null
+++ b/doc/filesInReleaseNotes.md
@@ -0,0 +1,56 @@
+# Using the releases
+For each new *stable* version of Pinetime, a [release note](https://github.com/JF002/Pinetime/releases) is created. It contains a description of the main changes in the release and some files you can use to flash the firmware in your Pinetime.
+
+This page describes the files from the release notes and how to use them.
+
+**NOTE :** the files included in different could be different. This page describes the release note of [version 0.7.1](https://github.com/JF002/Pinetime/releases/tag/0.7.1), which is the version that'll probably be pre-programmed at the factory for the next batch of Pinetime devkits.
+
+## Files included in the release note
+
+### Standalone firmware
+This firmware is standalone, meaning that it does not need a bootloader to actually run. It is intended to be flash at offset 0, meaning it will erase any bootloader that might be present in memory.
+
+ - **pinetime-app.out** : Output file of GCC containing debug symbols, useful is you want to debug the firmware using GDB.
+ - **pinetime-app.hex** : Firmware in Intel HEX file format. Easier to use because it contains the offset in memory where it must be flashed, you don't need to specify it.
+ - **pintime-app.bin** : Firmware in binary format. When programming it, you have to specify the offset (0x00) in memory where it must be flashed.
+ - **pinetime-app.map** : Map file containing all the symbols, addresses in memory,...
+ 
+**This firmware must be flashed at address 0x00 in the main flash memory**
+
+### Bootloader
+The bootloader  is maintained by [lupyuen](https://github.com/lupyuen) and is a binary version of [this release](https://github.com/lupyuen/pinetime-rust-mynewt/releases/tag/v4.1.7).
+
+ - **bootloader.hex** : Firmware in Intel HEX file format.
+ 
+ **This firmware must be flashed at address 0x00 in the main flash memory**
+
+
+### Graphics firmware 
+This firmware is a small utility firmware that writes the boot graphic in the external SPI flash memory. You need it if you want to use the [bootloader](../bootloader/README.md).
+
+ - **pinetime-graphics.out** : Output file of GCC containing debug symbols, useful is you want to debug the firmware using GDB.
+ - **pinetime-graphics.hex** : Firmware in Intel HEX file format. Easier to use because it contains the offset in memory where it must be flashed, you don't need to specify it.
+ - **pintime-graphics.bin** : Firmware in binary format. When programming it, you have to specify the offset (0x00) in memory where it must be flashed.
+ - **pinetime-graphics.map** : Map file containing all the symbols, addresses in memory,...
+ 
+**This firmware must be flashed at address 0x00 in the main flash memory**
+
+### Firmware with bootloader
+This firmware is intended to be used with our [MCUBoot-based bootloader](../bootloader/README.md).
+
+ - **pinetime-mcuboot-app-image.hex** : Firmware wrapped into an MCUBoot image. This is **the** file that must be flashed **@ 0x8000** into flash memory. If the [bootloader](../bootloader/README.md) has been successfully programmed, it should run this firmware after the next reset.
+
+The following files are not directly usable by the bootloader:
+
+ - **pinetime-mcuboot-app.bin** : Output file of GCC containing debug symbols, useful is you want to debug the firmware using GDB.
+ - **pinetime-mcuboot-app.hex** : Firmware in Intel HEX file format. 
+ - **pinetime-mcuboot-app.bin** : Firmware in binary format. 
+ - **pinetime-mcuboot-app.map** : Map file containing all the symbols, addresses in memory,...
+
+### OTA (Update the firmware Over-The-Air)
+Once the bootloader and application firmware are running, it is possible to update the current firmware or even replace it with another firmware **that uses the same bootloader based on MCUBoot**.
+
+**NOTE :** Use this file **only** if you programmed our [MCUBoot-based bootloader](../bootloader/README.md). This file is not compatible with other bootloaders like the one that is based on the closed source NRF SoftDevice !
+
+ - **pinetime-app-dfu.zip** : This is the file you must provide toNRFConnect to update the firmware over BLE.
+