Save bond information in the FS after a disconnect or encryption change
if the bond is not already stored. The bond is restored on boot enabling
automatic reconnection to a previously bonded central.
Two consecutive watch reboots with the central out of range (or BLE off)
will remove the stored bond from the watch.
This commit adds the following:
Passkey pairing - passkey is displayed on watch
Swipe down to clear passkey screen
Connection encryption
Connection bonding
Automatic reconnects to a bonded peripheral
Trusted device on Android
Note that persisting the bond between reboots is NOT included in
this commit. Therefore, rebooting the watch will cause reconnect failures.
You must delete the bond from the phone to reconnect/pair.
Don't use relative imports like `../foo.h` as those depend on the
relative position of both files. Rather than that use imports relative
to the `src` directory, which explicitly is part of the include
directories.
* docs: Fix a few typos
There are small typos in:
- doc/versioning.md
- src/components/ble/NimbleController.cpp
- src/libs/mynewt-nimble/CODING_STANDARDS.md
- src/libs/mynewt-nimble/docs/btshell/btshell_GAP.rst
- src/systemtask/SystemTask.cpp
Fixes:
- Should read `milliseconds` rather than `miliseconds`.
- Should read `unnecessary` rather than `uncesseray`.
- Should read `target` rather than `tharget`.
- Should read `project` rather than `projct`.
- Should read `preferred` rather than `prefered`.
- Should read `functioning` rather than `functionning`.
- Should read `forever` rather than `forver`.
- Should read `existing` rather than `exisiting`.
On power up, advertise aggressively for at least 30 seconds then switch
to a longer interval to conserve battery life. This fast/slow pattern
is designed to balance connection response time and battery life.
When a disconnect event is received restart the fast/slow pattern.
When a failed connect event is received, restart the fast/slow pattern.
When the screen is activated and ble is not connected, restart the fast/slow pattern.
This pattern is consistent with Apple's BLE developer standards (QA 1931).
Start advertising aggressively when powered on then
slow down linearly over 75 seconds. This will conserve
battery by not advertising rapidly the whole time we
are seeking a connection. The slowest rate is
approximately once every 4.5 seconds to balance
responsiveness and battery life.
We use a fixed advertising duration of 5 seconds and start
with a 62.5 ms advertising interval. Every 5 seconds
(the advertising duration) we step up to a larger
advertising interval (slower advertising). We continue
to increase the advertising interval linearly for
75 seconds from the start of advertising. At 75 seconds
we have an advertising interval of 4.44 seconds which we
keep until connected. A reboot will restart the sequence.
When we receive a disconnect event we restart the sequence
with fast advertising and then slow down as described above.
Note that we are not using the BLE high duty cycle setting to
change the advertising rate. The rate is managed by repeatedly
setting the minimum and maximum intervals.
The linear rate of decrease and the slowest interval size
were determined experimentally by the author. The 5.3 Core
spec suggests that you not advertise slower than once
every 1.2 seconds to preserve responsiveness but we
ignored that suggestion.
Instead of casting the UUID object to the ble_uuid_t* used throughout
the NimBLE API just pass the address of the ble_uuid_t member that's at
the start of each of the UUID structs.
Fixed mismatch between the service and characteristic IDs in the
navigation service comments and documentation. They had old values not
reflecting the current code and changes in doc/ble.md
* Make firmware updating more foolproof and fix bugs
* No need to manually handle overflow
* Make startTime TickType_t
* Don't process TouchEvents::None
* Fix sleep getting re-enabled issue more directly
* Retrieve and display bootloader version
- Display bootloader version on System Info screen
- Enable SPI flash sleep mode if bootloader version >= 1.0.0
* Wait for SPI flash to wakeup before starting OTA DFU
- Enable LVGL animation (and disable groups, which were not used), and set the speed.
- Fix disc animation and progress display by initializing lastIncrement at 0 (a random value will be used otherwise, in release build)
If the buffer does not contain any \0, the whole buffer is considered to be the message of the notification. A default title will be displayed in the notification app.
